Miscellaneous Kits & Special Kits
APPLICATION
SIZE
KIT P/N
INSERT P/N
10X1.5
GM Aluminum block
Starter bolt repair
Starter bolt
The depth of the starter bolt hole should be 1.500″ or 38mm Deep.
M10x1.5
Starter Bolt
P/n 1380
Kit includes: Core Drill,
tap , tap guide, Driver, 4 inserts 20mm, 4 sleeves
10153
APPLICATION
SIZE
KIT P/N
INSERT P/N
3/8-16
GM cast iron block
stripped Starter bolt thread repair kit
Stripped Starter bolt
The depth of the starter bolt hole should be 1.200″ inches or 30mm Depth minimum.
Note: This kit can also repair a failed helicoil or coil style insert.
3/8-16
3/8-16 Starter Bolt
V8
P/N 1535
153501
APPLICATION
SIZE
KIT P/N
INSERT P/N
Montero sr crank bolt
Same as below kit with square on drill
Link to repair on 4×4
Click for repair
M14x1.5
Short drill
See Note here:
P/n 1415H
This kit includes a shorter drill with a square so you can turn it with a 1/2″12 point socket by hand.
14159
carbon steel
insert
APPLICATION
SIZE
KIT P/N
INSERT P/N
KIA crank shaft bolt thread repair kit where the thread start flush on the crank shaft on Kia.
M14x1.5
S&D drill
6″ long need
1/2 drill motor
p/n1415N
Kit includes: Drill, Counterbore
tap , tap guide, Driver, 5 inserts 28mm stainless
141556
APPLICATION
SIZE
KIT P/N
INSERT P/N
M8x1.25 kit includes:
Coredrill, , tap, driver, 5 Stainless steel inserts of the 11.7mm no flange.
18122NF
APPLICATION
SIZE
KIT P/N
INSERT P/N
M18x1.5
O2 SENSOR
THREAD REPAIR KIT
M18x1.5
kit includes:
Reamer 3.200 inches length, tap 4.500 inches length,
tap guide install driver 4.00 inches length, 5 inserts 7.5mm stainless.
18122NF
APPLICATION
SIZE
KIT P/N
INSERT P/N
M18x1.5
O2 SENSOR
THREAD REPAIR KIT
1/4-28 Special
KIT p/n 01488
PTI-Sert p/n 014888
——-
2610546
APPLICATION
SIZE
KIT P/N
INSERT P/N
1/4-28 Oversized
use after helicoil pulls out.
Must install smaller insert p/n 014888
Inside oversized insert.
KIT p/n 01489
PTI-SERT p/n 014899
——–
2610547
Bendix AirCraft Wheel
Oversized
1/4-28 Oversized
use after helicoil pulls out.
Must install smaller insert p/n 014888
Inside oversized insert.
KIT p/n 01489
PTI-SERT p/n 014899
——–
2610547
APPLICATION
SIZE
KIT P/N
INSERT P/N
M10x1.5 30mm
FLUSH SURFACE KIT
The 30mm length insert requires a special driver with reduced shank.
M10x1.5 kit includes:
Drill, counterbore, tap, reduced shank driver, 5 inserts of the 30mm length and tap guide.
10159
APPLICATION
SIZE
KIT P/N
INSERT P/N
Rocker Arm
M10x1.5 CORE KIT
The core drill included will allow a 11mm length insert to be installed deeper than the standard kit.
M10x1.5
kit includes:
Coredrill, tap, driver, tap guide, 5 inserts 11mm length.
The mechanic doing the repair will have to set the counterbore depth manually by hand.
101511
APPLICATION
SIZE
KIT P/N
INSERT P/N
Rocker Arm
M8x1.25 CORE KIT
The core drill included will allow a special 11.7mm length no flange insert to be installed deeper than the standard kit.
M8x1.25
kit includes:
Coredrill, tap, driver, tap guide, 5 inserts of the 11.7mm no flange.
The mechanic doing the repair will have to set the counterbore depth manually by hand.
18125117N
Rocker Arm
M8x1.25 BIG-SERT
OverSized repair
Use after:
A helicoil has failed
The core drill included will allow a special 11.7mm length BIG-SERT insert to be installed deeper than the standard kit.
M8x1.25
kit includes:
Coredrill, tap, driver, tap guide, 5 inserts of the 11.7mm
The mechanic doing the repair will have to set the counterbore depth manually by hand.
58121
Transmission pan
M8x1.25 CORE KIT
This kit has a FIXED stop collar for FLUSH repair.
The kit installs the insert flush to the surface in the limited space of the transmission pan bolt holes.
M8x1.25
kit includes:
Coredrill, tap, driver, tap guide, 5 inserts of the 11.7mm no flange.
18125117N
APPLICATION
SIZE
KIT P/N
INSERT P/N
M8x1.25 CORE KIT
Extended
5″ inch length tools
The core drill included will allow a 16.2mm length insert to be installed deeper than the standard kit.
M8x1.25
kit includes:
5″ inch length tools
Coredrill, tap, driver,
5 inserts of the
no flange 16.2mm length.
The mechanic doing the repair will have to set the counterbore depth manually by hand.
18125162N
APPLICATION
SIZE
KIT P/N
INSERT P/N
M6x1.0 Extended kit
This tooling has no counterbore.
The hole must be at least 8mm or .315 inches for the tap to access the hole.
This kit is typically used inMercedes injector clamp bolt Thread repair
Mercedes injector bolt thread repair kit
M6x1.0 Extended kit
includes:
6″ extension drill,
4″ tap, 4″ driver,
5 inserts of a 17mm length.
KIT p/n 1610E2
THIS KIT HAS BECOME OBSOLETE BECAUSE CUSTOMERS COMPLAINED OF TOOLS BREAKING.
Commonly used in Dodge sprinter stripped injector hold down clamp bolt
16107
APPLICATION
SIZE
KIT P/N
INSERT P/N
DIESEL INJECTOR
M24x2.0
KIT p/n 2420
24201
APPLICATION
SIZE
KIT P/N
INSERT P/N
BIG-SERT
M10x1.5
OVERSIZED
M10x1.5
Kit includes:
Drill, Counterbore, Tap, tap guide, install driver and
5 inserts of the 24.5mm length.
KIT p/n 5015D
50155
APPLICATION
SIZE
KIT P/N
INSERT P/N
M14x1.25
SPARK PLUG
or Drain pan
OPTIONAL TOOLING
FOR 7mm INSERTS
M14x1.25
Kit includes:
Drill, Counterbore, Tap, tap guide, install driver and
5 inserts of the 7mm length.
KIT p/n 14125D
44121
APPLICATION
SIZE
KIT P/N
INSERT P/N
NAVISTAR DPF M12x1.25
p/n 12-235-02
M12x1.25
12-235-02
12-235-02-06
Used to renew stripped-out temperature and pressure sensor threads on DOC/DPF units.
APPLICATION
SIZE
KIT P/N
INSERT P/N
2007 MaxxForce 10, 2007 MaxxForce 11, 2007 MaxxForce 13, 2007 MaxxForce 7, 2007 MaxxForce 9, 2007 MaxxForce DT, 2010 MaxxForce 10, 2010 MaxxForce 11, 2010 MaxxForce 13, 2010 MaxxForce 15, 2010 MaxxForce 7,
NAVISTAR DPF M14x1.5
p/n 12-235-03
M14x1.5
12-235-03
12-235-03-06